Screen Printer NPM-GP/L
Screen Printer NPM-GP/L
Edge devices, automation functions, and 5M process control to make autonomous factories a reality
- 5M process control
- Material and machine condition monitoring to automatically change machine parameters
- M2M function with inspection machines to optimize printing position and volume
- Supporting automation functions
- Automated model changeover work
- Automated work during production
- Improved basic performance
- Printing cycle time: 12 seconds, repeatability of positioning: ± 3.8 μm
- Supporting high accuracy/density printing
Features and Benefits of “Screen Printer NPM-GP/L”
Monitoring and control of material and machine condition using APC-5M
Solder viscosity feedback (optional)
The viscosity of solder on the mask is measured and controlled to maintain the proper viscosity.
Mask tension feedback (option)
Measure mask tension before screen printing and change plate snap off operation.
Cleaning solvent discharge feedback (option)
Monitor solvent discharge when wet-cleaning to maintain the proper discharge.
M2M function with inspection machines to optimize printing position and volume
Changing each condition (printing pressure, squeegee speed, and snap-off speed) based on SPI results makes it possible to reach and maintain optimum printing conditions.
Printing position and volume are automatically corrected based on SPI results. Two options are available: Position correction and volume correction.
APC-FB (volume) controls volume by changing the squeegee angle, making it possible to smoothly reach and maintain optimum printing conditions.
APC-FB (position) (option)
APC-FB (volume) (option)*
* The angle variable squeegee (option) is required.
Enhancement of automation and labor-saving functions
Options for automated changeover
Solder transfer (option)
Automatic collection of solder on mask after printing and automatic feeding of solder on mask for the next production model.
Metal Mask changer (option)
Automatic storing of the mask after the end of production in a magazine at the rear of the machine, and placement of another mask to be used for the next production model in the machine. Capable of stocking up to 10 masks in the magazine and taking masks in and out during production.
Support pin automatic exchange (option)
Automated collection/arrangement of support pins during changeover to save manpower.
Options for automated production
Perforated pot type automatic solder supply (option)
Solder supply automated to promote labor saving and operation without interruption.
Paper-free wiping unit (option)
Cleaning without using cleaning paper or solvents Use of paper and solvents can be reduced.
Solder leak prevention block (option)
Magnet reaction force achieves contact with the mask to reduce lateral solder leakage in printing. Simple structure for easy cleaning.
Supporting high accuracy/density printing
Attack angle variable squeegee (option)
The set squeegee angle can be adjusted, using the front and rear squeegee vertical axes, between 45° and 70° in 1 degree increments.
Top/side clamper (movable type) (Option)
Pressing down on PCB edge faces increases screen printing quality of warped PCB.
Either PCB upper or side face can be selected for correction.
New operation panel
A large-sized panel (15-inch) introduced to increase ease of use and visibility.
Screen configuration reviewed (a reduction in the number of screens) to decrease the screen handling time required.
Introduction video of “Screen Printer NPM-GP/L”
Related products
Related product series
Installed MES software
PanaCIM-EE Gen2
Support is provided for improvement in QCD in each task related to mounting, through centralized management of the entire mounting floor
Integrated line management system
iLNB
Optimization of the entire production line by “connecting” Panasonic machines, non-Panasonic machines, and higher-level systems
Exhibition and Seminar Information
Information on current seminars and exhibitions is compiled and posted here. Information on past seminars and exhibitions is also available.
Custom Service
Line simulation
Tact simulation can be performed according to the mounted components and supply form.
Mounting feasibility study (nozzle selection)
We propose the optimum nozzle for the mounted components
Maintenance solution
To ensure that our mounting machines can be reliably used by our customers for many years after delivery, we not only maintain the machines, but also continue to support our customers throughout the life span of the machines, reducing production loss, stabilizing operation and improving work efficiency.